Blind shear ram blowout preventers: Estimation of shear force and optimization of ram geometry
Başlık çevirisi mevcut değil.
- Tez No: 401105
- Danışmanlar: PROF. TAYLAN ALTAN, DR. CHANGHYOK CHOI
- Tez Türü: Yüksek Lisans
- Konular: Makine Mühendisliği, Mechanical Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2010
- Dil: İngilizce
- Üniversite: The Ohıo State Unıversıty
- Enstitü: Yurtdışı Enstitü
- Ana Bilim Dalı: Belirtilmemiş.
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: Belirtilmemiş.
Özet
Özet yok.
Özet (Çeviri)
The explosion of the Deepwater Horizon oil rig in the Gulf of Mexico showed once again that during the oil drilling operation any failures of surface equipment which is called blowout preventers (BOPs) may result in death, injury and massive oil spills that have huge impact on the environment. The blowout preventers are devices that are supposed to close off the wellbore and seal it in an emergency to prevent formation fluid from reaching the surface of the well. In a blowout preventer stack, which consists of several types of blowout preventers, the last line of defense is the blind shear ram that is supposed to close and seal the wellbore by shearing through the drill string or any other tubing when they are in the wellbore. According to a recent report prepared for the U.S. Minerals Management Services (MMS) by [Childs et al., 2004], two of the three BOP manufacturers rely on a very basic equation“the Distortion Energy Theory shear equation”to estimate the shear force requirement for shearing operation. However with recent advancement in drill pipe materials, it might not be sufficient to estimate the actual shear force to shear a specific drill pipe using yield or tensile stress by itself and the Distortion Energy Theory shear equation. Using finite element method to analyze the drill pipe materials and dimensions and simulate the entire shearing and sealing operation with blowout preventer working conditions through the finite element method can provide good approximation for actual shear force and sealing pressure to secure the well. Also, the finite element method could be used to optimize shear ram geometry so that minimum force and energy are used to shear the tube by plastic deformation. Fourteen task studies are presented throughout this research. The first two tasks were studied to develop a methodology to evaluate the required shear force to shear a certain drill pipe without considering blowout preventer working conditions effect on shearing operation. The results of these studies were compared with actual shear forces that were obtained from BOP manufacturers [Childs et al., 2004]. The next three tasks were studied to determine a relation between drill pipe diameters and shear force requirement for shearing operations. Tasks 6 to 9 were studied to evaluate the effect of the vertical load that stems from the weight of drill string on shear force requirement. The last five tasks were studied to optimize tool clearance to minimize the actual shear force. It is shown that shear forces evaluated by using finite element method (FEM-Deform 3D) simulations provided fairly accurate results for actual shear force. Also, it is found that by using FEM simulation the effect of the blowout preventer working condition on shearing operation can be estimated and ram geometries can be optimized. Therefore, FEM simulation can be used to design more reliable and efficient ram type blowout preventers.
Benzer Tezler
- Bir pamuk iplikhanesinde fiili çalışma metodlarının incelenmesi ve mevcut işlemlerin standart sürelerinin saptanması
Başlık çevirisi yok
MÜRŞİDE KESEROĞLU
Yüksek Lisans
Türkçe
1985
İşletmeEge ÜniversitesiTekstil Mühendisliği Ana Bilim Dalı
DOÇ. DR. MUSTAFA NAZMİ ERCAN
- Pamuk ipliklerinde istatiksel bir hata analiz yönteminin geliştirilmesi üzerinde araştırmalar
Başlık çevirisi yok
AYŞE KARAKOR
Yüksek Lisans
Türkçe
1986
Tekstil ve Tekstil MühendisliğiEge ÜniversitesiTekstil Mühendisliği Ana Bilim Dalı
DOÇ. DR. GÜNGÖR BAŞER
- Krem tip eritme peynir imalat teknolojisi
Başlık çevirisi yok
GÜL FİGEN AR
Yüksek Lisans
Türkçe
1986
Gıda MühendisliğiEge ÜniversitesiGıda Mühendisliği Ana Bilim Dalı
DOÇ. DR. MUSTAFA ÜÇÜNCÜ
- Türkiye'de üretilen bazı kışlık el örgü ipliklerinin başlıca iplik ve lif özellikleri üzerinde bir araştırma
Başlık çevirisi yok
SEMA YÜCEBAŞ
Yüksek Lisans
Türkçe
1986
Tekstil ve Tekstil MühendisliğiEge ÜniversitesiTekstil Mühendisliği Ana Bilim Dalı
PROF. DR. GÜLSEREN YAZICIOĞLU
- Halı ipliği yapımında kullanılan yünlerin teknolojik özellikleri üzerinde araştırmalar
Investigations on the technological properties of wools which are used in woollen carpet yarn production
BEKİR YILMAZ
Doktora
Türkçe
1985
Tekstil ve Tekstil MühendisliğiEge ÜniversitesiTarım Ürünleri Teknolojisi Ana Bilim Dalı
PROF. DR. MUSTAFA HARMANCIOĞLU