AA2024 esaslı nanopartikül takviyeli hibrit kompozit yatak malzemelerinin üretimi ve tribolojik özelliklerinin incelenmesi
Production of AA2024 based nanoparticle reinforced hybrid composite bearing materials and investigation of tribological properties
- Tez No: 904251
- Danışmanlar: PROF. DR. AYKUT ÇANAKÇI
- Tez Türü: Doktora
- Konular: Metalurji Mühendisliği, Metallurgical Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2024
- Dil: Türkçe
- Üniversite: Karadeniz Teknik Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Metalurji ve Malzeme Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Malzeme Bilim Dalı
- Sayfa Sayısı: Belirtilmemiş.
Özet
Bu çalışmanın amacı, toz metalurjisi ve mekanik öğütme yöntemleri kullanılarak nanoparçacık takviyeli AA2024 matrisli kompozit yatak malzemelerinin üretilmesi ve parçacık türü ile miktarının kompozit yatak malzemelerinin özelliklerine olan etkisinin araştırılmasıdır. Öğütme süresi 8 saat olarak optimize edildikten sonra farklı takviye oranlarına (ağırlıkça %0-2) sahip Al/B4C, Al/Grafit, Al/Grafen ve Al/KNT nanokompozitleri ile Al/B4C/Grafit, Al/B4C/Grafen ve Al/B4C/KNT hibritleri üretilmiştir. Üretilen numunelerin fiziksel ve mekanik özelliklerine takviye türü ve oranlarının etkisi; toz karakterizasyonu, mikroyapı ve faz analizi, bağıl yoğunluk ölçümleri, sertlik, çekme, aşınma ve korozyon testleri ile incelenmiştir. Elde edilen sonuçlara göre, nanokompozitler arasında en yüksek sertlik ve çekme mukavemeti, B2 numunesinde sırasıyla 181 HB ve 328 MPa olarak, hibrit nanokompozitlerde ise HG2 numunesinde sırasıyla 164 HB ve 314 MPa olarak elde edilmiştir. Ayrıca, en düşük aşınma oranı düşük yük altında AA2024/B4C/Grafit hibrit nanokompozitlerde, yüksek yük altında ise Al/B4C/Grafen hibrit nanokompozitlerde gözlemlenmiştir.
Özet (Çeviri)
The purpose of this study is to produce nanoparticle-reinforced composite bearing materials with an AA2024 matrix using powder metallurgy and mechanical milling methods and to investigate the effects of particle type and content on the properties of these composite bearing materials. After optimizing the milling duration to 8 h, Al/B4C, Al/Graphite, Al/Graphene, and Al/CNT nanocomposites, along with Al/B4C/Graphite, Al/B4C/Graphene, and Al/B4C/CNT hybrids, were produced with varying reinforcement ratios (0-2 wt%). The effects of reinforcement type and ratio on the physical and mechanical properties of the produced samples were examined through powder characterization, microstructure and phase analysis, relative density measurements, hardness, tensile, wear, and corrosion tests. According to the results, among the nanocomposites, B2 achieved the highest hardness and tensile strength, with values of 181 HB and 328 MPa, respectively. For the hybrid nanocomposites, the HG2 sample achieved the highest values, with hardness and tensile strength of 164 HB and 314 MPa, respectively. Furthermore, the lowest wear rate was observed in the Al/B4C/Graphite hybrid nanocomposites under low load, and in the Al/B4C/Graphene hybrid nanocomposites under high load.
Benzer Tezler
- AA 2014 alüminyum alaşımlarının ingot homojenizasyonunun sıcak işlenebilirliğe etkisi
Effect of different homogenisation treatment on the hot warkability of aluminium alloys AA 2014
MEHMET GAVGALI
- Atomize tozların tane dağılımının istatistik analizi
Statistical analysis of particle size distrubution of atomised powders
AHMET TAŞKAN
- AA 2014 matrisli-B4C parçacık takviyeli kompozit üretimi ve özelliklerinin incelenmesi
Manufacturing of AA 2014 Matrix-B4C particulate composites and investigating properties
AYKUT ÇANAKÇI
Yüksek Lisans
Türkçe
1998
Makine MühendisliğiKaradeniz Teknik ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
PROF. DR. FAZLI ARSLAN
- Al2O3 partikül takviyeli Al-Cu esaslı metal matriksli kompozit malzeme üretimi
Production of Al2O3 particle reinforced Al-Cu based metal matrix composite material
ÜMİT GENCAY BAŞCI
Yüksek Lisans
Türkçe
1999
Metalurji Mühendisliğiİstanbul ÜniversitesiMetalurji Mühendisliği Ana Bilim Dalı
PROF. DR. İBRAHİM YUSUFOĞLU