Geri Dön

Technology and optimization of PECVD dielectric films for M(O)EMS applications

Başlık çevirisi mevcut değil.

PDF İndir

  1. Tez No: 727481
  2. Yazar: EGEMEN KEÇECİ
  3. Danışmanlar: DR. MİCHAł JóZWİK
  4. Tez Türü: Yüksek Lisans
  5. Konular: Mekatronik Mühendisliği, Mechatronics Engineering
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 2019
  8. Dil: İngilizce
  9. Üniversite: Warsaw Unıversıty Of Technology
  10. Enstitü: Yurtdışı Enstitü
  11. Ana Bilim Dalı: Belirtilmemiş.
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: Belirtilmemiş.

Özet

Özet yok.

Özet (Çeviri)

The thesis is devoted to the technology of dielectric films fabricated by means of Plasma Enhanced Chemical Vapor Deposition (PECVD) process for the applications in M(O)EMS devices. Technological fabrication process of exemplary M(O)EMS, here represented by cantilever. Optimization of PECVD dielectric film is proposed. Introduction contain the literature search. It begins with M(O)EMS technology's past and future. Essentials of fabrication are briefly explained. Properties of silicon and silicon compounds are presented. Finally, characterization methods of MEMS products are depicted. Laboratory work is divided in two parts. In the first part of the work, the aim is to optimize the fabrication of thin film dielectric films (e.g., silicon nitride – SiNx). We require to have the control of the thickness, stoichiometry (refractive index) and level of internal stress of the dielectric material by using appropriate PECVD process' parameters. We need to investigate the influence of process' parameters onto electrophysical properties of obtained SiNx films and try to find the correlations in order to get set of process' parameters to obtain appropriate properties of dielectric film. Taguchi's method was used for optimization of deposition. Thickness and refractive index of films are measured by spectroscopic ellipsometry. At the end of the first part the design of SiNx cantilever fabrication process was proposed, however due to technical problems in the clean room, test structures cannot be fabricated. For this reason, objects with closest specification fabricated in the past were used as test structures. The aim of the second part of the work is characterization of free-standing MEMS structures. Fabricated silicon cantilever with a dielectric layer of SiOxNy deposited by PECVD is investigated by laser interferometry. Chapter 4 presents the principles of interferometry and Twyman-Green interferometer setup that was used in this work. As cantilever was tested in static and dynamic mode, stroboscopic interferometry and time average interferometry are elucidated. The results of characterization are used for evaluation of structure's mechanical performance and as feedback data to optimization of fabrication process. Additionally, numerical models were analyzed to understand the influence of residual stress in deposited layer on static deflection and its resonance frequencies. Static analysis provided value of residual stress equal 370MPa. Modal analysis showed that effect of residual stress, for this geometrical configuration of cantilever, isn't significant on frequency.

Benzer Tezler

  1. Tez No

    199018

    Silicon based dielectrics: Growth, characterization, and applications in integrated optics

    Silisyum tabanlı dielektrikler: Tümleşik optikte kullanıma yönelik büyütme ve inceleme

    FERİDUN AY

    Doktora

    İngilizce

    İngilizce

    2005

    Elektrik ve Elektronik Mühendisliğiİhsan Doğramacı Bilkent Üniversitesi

    Elektrik-Elektronik Mühendisliği Ana Bilim Dalı

    PROF. DR. ATİLLA AYDINLI

  2. Tez No

    767449

    Optimization and characterization of polysilicon fabricated by e-beam evaporation for passivating contact silicon (topcon) solar cells

    Pasifleştiren kontaklı silisyum tabanlı güneş hücresi (topcon) uygulamaları için elektron demeti ile üretilmiş polisilisyum yapıların optimizasyonu ve karakterizasyonu

    SALAR HABİBPUR SEDANİ

    Doktora

    İngilizce

    İngilizce

    2022

    EnerjiOrta Doğu Teknik Üniversitesi

    Mikro ve Nanoteknoloji Ana Bilim Dalı (disiplinlerarası)

    PROF. DR. RAŞİT TURAN

    PROF. DR. HÜSNÜ EMRAH ÜNALAN

  3. Tez No

    134268

    Optimization of a hybrid combination of a photovoltaic system and a wind energy conversion system: İzmir Institute of Technology campus area case

    Bir rüzgar enerjisi değişim sistemi ile bir fotovoltaik sistemin oluşturduğu hibrid bileşimin optimizasyonu: İzmir Yüksek Teknoloji Enstitüsü kampüs alanı durumu

    ORHAN EKREN

    Yüksek Lisans

    İngilizce

    İngilizce

    2003

    Enerjiİzmir Yüksek Teknoloji Enstitüsü

    Enerji Mühendisliği Ana Bilim Dalı

    DOÇ. DR. BARIŞ ÖZERDEM

  4. Tez No

    544325

    Geleceğin teknolojisi yenilenebilir enerji sistemlerine geçişte çanakkale yöresi elektrik şebekelerinin mevcut durumu ve optimizasyonu

    Current status and optimization of electrical grids in Çanakkale region for renewable energy systems as future technology

    YILDIRAY ÖZGÖREN

    Yüksek Lisans

    Türkçe

    Türkçe

    2019

    Elektrik ve Elektronik MühendisliğiÇanakkale Onsekiz Mart Üniversitesi

    Enerji Kaynakları ve Yönetimi Ana Bilim Dalı

    PROF. DR. SERMET KOYUNCU

  5. Tez No

    794624

    Development and comparison of three algorithms used in mppt technology to extract maximum power from photovoltaic system in matlab/simulink

    Matlab/simulink'te fotovoltaik sistemden maksimum güç elde etmek için mppt teknolojisinde kullanılan üç algoritmanın geliştirilmesi ve karşılaştırılması

    ALAA SHAKIR MHMOOD AL-ARJEELI

    Yüksek Lisans

    İngilizce

    İngilizce

    2022

    Elektrik ve Elektronik MühendisliğiÇankırı Karatekin Üniversitesi

    Elektrik ve Elektronik Mühendisliği Ana Bilim Dalı

    DR. ÖĞR. ÜYESİ MUSTAFA TEKE

Geri Dön