Strain measurements on Fe, Niand NiFe embedded carbon fiberepoxy composite
Başlık çevirisi mevcut değil.
- Tez No: 717481
- Danışmanlar: PROF. NİCOLA MORLEY
- Tez Türü: Yüksek Lisans
- Konular: Kimya Mühendisliği, Chemical Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2020
- Dil: İngilizce
- Üniversite: The Unıversıty Of Sheffıeld
- Enstitü: Yurtdışı Enstitü
- Ana Bilim Dalı: Belirtilmemiş.
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: Belirtilmemiş.
Özet
Özet yok.
Özet (Çeviri)
The magnetisations of a woven carbon/epoxy composite embedded with ~1 volume percent of Fe, Ni and NiFe powder particles (6-200 µm) were measured at the tensile strains from 0.833 to 1.6 mstrain. The powder embedded composite test plates (1x25x50 mm) were strained using a bending ring test apparatus with various bend radius. The magnetisation of loaded composite samples was measured before and during loading using a 3D Anisotropic Magneto-Resistance sensor in three directions. The maximum change of magnetisation was measured in the z-axis, normal to the loading direction, and there was almost no change of magnetisation in x and yaxis. The total change of magnetisation was found to be parallel with the change of magnetisation in the z-axis. The composites embedded with the particles less than 80 µm showed an increasing change of magnetisation with increasing bending strain. The determined piezo-magnetic stress and strain coefficients of the composites embedded with less than 80 µm particles were shown to be similar with those of similar composites tagged with Terfenol-D particles. The results also showed that magnetic Fe and Ni particle addition to composites can be used to measure strain within the composites remotely for structural health monitoring. The errors in magnetisation measurements including the sensor-sample distance and the stress state (reduction of the tensile stress in the thickness direction) are discussed. In order to prevent the stress state effect, powder addition to only the upper and lower surfaces of the composite plate is recommended. The studied powder added composite should be further investigated for optimum powder size in order to increase the accuracy of magnetisation measurements.
Benzer Tezler
- Kobalt esaslı alaşımların bağlayıcı matris olarak kullanıldığı doğal taş kesiminde kullanılan elmas kesici uçların karakterizasyonu
Characterization of diamond cutting tools using cobalt base alloys as the binding matrices
FERİT TOPALOĞLU
Yüksek Lisans
Türkçe
2013
Metalurji Mühendisliğiİstanbul Teknik ÜniversitesiMetalurji ve Malzeme Mühendisliği Ana Bilim Dalı
PROF. DR. EYÜP SABRİ KAYALI
- Fe bazlı alaşımların yapısal ve mekanik özelliklerinin incelenmesi
Investigation of structural and mechanical properties of Fe-based alloys
ESRA YÜKSEL
Yüksek Lisans
Türkçe
2011
Fizik ve Fizik MühendisliğiNiğde ÜniversitesiFizik Ana Bilim Dalı
YRD. DOÇ. DR. SELVA BÜYÜKAKKAŞ
- Tungsten ağır alaşımlarının yüksek gerinme hızlarında deformasyonunun deneysel ve sayısal yöntemler ile araştırılması
Investigation of high strain rate deformation of tungsten heavy alloys with experimental and numerical methods
HAKAN HAFIZOĞLU
Doktora
Türkçe
2019
Makine MühendisliğiTobb Ekonomi ve Teknoloji ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
PROF. DR. NURİ DURLU
- Paslanmaz çeliklere uygulanan düşük sıcaklık nitrürleme işleminin mekanik ve korozyon özelliklerine etkisi
The effect of low temperature nitriding on mechanical and corrosion properties of stainless steels
ÖZGÜR ÇELİK
Doktora
Türkçe
2010
Metalurji Mühendisliğiİstanbul Teknik Üniversitesiİleri Teknolojiler Ana Bilim Dalı
PROF. DR. EYÜP SABRİ KAYALI
- Yüksek karbonlu bir çeliğin mikroyapı ve mekanik özelliklerine izotermal tavlamanın etkisi
Effect of isothermal annealing on microstructure and mechanical properties of a high carbon steel
MUSTAFA SERDAR KUZYAKA
Yüksek Lisans
Türkçe
2014
Metalurji Mühendisliğiİstanbul Teknik ÜniversitesiMalzeme Bilimi ve Mühendisliği Ana Bilim Dalı
DOÇ. MURAT BAYDOĞAN