Hızlı sinterlenen zirkonyum dioksit seramiklerin karakterizasyonu ve hızlı yaşlandırma işleminin etkisi
Characterization of speed sintering zirconium dioxide ceramics and the influence of accelerated aging
- Tez No: 656163
- Danışmanlar: PROF. DR. KÜRŞAT ESER
- Tez Türü: Diş Hekimliği Uzmanlık
- Konular: Diş Hekimliği, Dentistry
- Anahtar Kelimeler: Dental porselen, Dental restorasyon, Dental stres analizi, Sinterleme, Yapay yaşlandırma, Zirkonyum, Dental porcelain, Dental restoration, Dental stress analysis, Sintering, Artificial aging, Zirconium
- Yıl: 2020
- Dil: Türkçe
- Üniversite: Gazi Üniversitesi
- Enstitü: Diş Hekimliği Fakültesi
- Ana Bilim Dalı: Protetik Diş Tedavisi Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: Belirtilmemiş.
Özet
Bu çalışmanın amacı, hızlı ve süper hızlı sinterleme prosedürlerinin ve hızlı yaşlandırma işleminin zirkonyum dioksit seramikler üzerindeki etkilerini değerlendirmektir. Çalışmada InCoris TZI ve InCoris ZI zirkonyum dioksit bloklardan elde edilen örneklere konvansiyonel, hızlı veya süper hızlı sinterleme prosedürleri uygulandı. Her sinterleme grubundaki örneklerin yarısına otoklavda 134°C sıcaklık ve 2 bar basınç altında 5 saat yaşlandırma uygulandı. Örneklerin bükülme dayanımı, yüzey sertliği ve kırılma tokluğu, kontrast oranı ve gren boyutu değerlendirildi. Örneklere SEM/EDS, AFM ve XRD analizleri uygulandı. Elde edilen veriler çok yönlü ANOVA ve Tukey testi ile istatistiksel olarak analiz edildi (p<0,05). Çalışma sonucunda; uygulanan sinterleme prosedürlerinin örneklerin bükülme dayanımı, kırılma tokluğu, faz dönüşümü, yüzey topografisi ve elemental kompozisyonu üzerinde anlamlı etkiye sahip olmadığı saptandı. Süper hızlı sinterlenen örneklerin gren boyutunun arttığı gözlendi. Süper hızlı sinterlemeyi takiben InCoris TZI örneklerin yüzey sertliğinin azaldığı, InCoris ZI örneklerin yüzey sertliğinin değişmediği görüldü. InCoris TZI örneklerin InCoris ZI örneklere kıyasla kontrast oranının daha yüksek olduğu, fakat sinterleme prosedürlerinin örneklerin kontrast oranı üzerinde anlamlı etkiye sahip olmadığı görüldü. Yaşlandırmayı takiben örneklerin bükülme dayanımı, kırılma tokluğu, yüzey sertliğinin azaldığı, faz dönüşümünün ve yüzey düzensizliklerinin arttığı, itriya element içeriğinin azaldığı, gren boyutunun etkilenmediği saptandı. Kontrast oranının sadece konvansiyonel sinterlenen InCoris TZI örneklerde yaşlandırma sonrası arttığı, diğer gruplarda anlamlı fark olmadığı bulundu.
Özet (Çeviri)
The aim of this study is to evaluate the effects of speed and super speed sintering procedures and accelerated aging on the characterization of zirconium dioxide ceramics. In the study, conventional, speed or super speed sintering procedures were applied to samples obtained from the InCoris TZI and InCoris ZI zirconium dioxide blocks. Half of the samples in each sintering group were aged in autoclave at 134 ° C and 2 bar pressure for 5 hours. The flexural strength, surface hardness and fracture toughness, contrast ratio and grain size of the samples were evaluated. SEM/EDS, AFM and XRD analyzes were applied to the samples. Data obtained were analyzed statistically with the multiway ANOVA and Tukey test (p <0.05). In the results of the study; it was determined that the applied sintering procedures did not have a significant effect on the flexural strength, fracture toughness, phase transformation, surface topography and elemental composition of the samples. It was observed that the grain size of the super speed sintered samples increased. Surface hardness of InCoris TZI samples decreased while surface hardness of InCoris ZI samples remained unchanged following super speed sintering. InCoris TZI samples were found to have a higher contrast ratio than InCoris ZI samples, but sintering procedures did not have a significant effect on the contrast ratio of the samples.After aging, it was determined that the flexural strength, fracture toughness, surface hardness of the samples decreased, phase transformation and surface irregularities increased, yttria element content decreased, and grain size was not affected. It was found that the contrast ratio increased only after aging in conventional sintered InCoris TZI samples, but there was no significant difference in the other groups.
Benzer Tezler
- Alumina ve silisyum karbürün mukavemet özellikleri üzerine üretim şartları ve bileşimin etkisi
The effect of composition and manufacturing methods on the strength properties of silicon carbide
İSMAİL YILDIRIM
Doktora
Türkçe
2003
Makine Mühendisliğiİstanbul Teknik Üniversitesiİleri Teknolojiler Ana Bilim Dalı
PROF. DR. ALAEDDİN ARPACI
- The effect of reactive sintering on the densification of boron carbide zirconium diboride composite
Reaktif sinterlemenin bor karbür zirkonyum diborür kompozitinin yoğunlaşması üzerindeki etkisi
ÖMER YÜCEL
Yüksek Lisans
İngilizce
2021
Seramik MühendisliğiEskişehir Teknik ÜniversitesiNanoteknoloji Ana Bilim Dalı
PROF. DR. SERVET TURAN
- Farklı sinterleme parametrelerinin ti-basedayanak üstü monolitik zirkonya restorasyonların kırılma dayanımlarına etkisinin incelenmesi
Effect of different sintering parameters on the fracture strenght of ti-base supported monolithic zirconia restorations
MUSTAFA KAANALP ERGÜL
Diş Hekimliği Uzmanlık
Türkçe
2022
Diş HekimliğiGaziantep ÜniversitesiProtetik Diş Tedavisi Ana Bilim Dalı
DOÇ. DR. FATİH SARI
- Zr02-Ca0-Mg0 esaslı oksijen sensörlerinin üretimi ve karakterizasyonu
Processing oxygen sensors with Zr02-Ca0-Mg0 and characterization
ERDEM KAZCI
Yüksek Lisans
Türkçe
2001
Metalurji Mühendisliğiİstanbul Teknik ÜniversitesiMetalurji Mühendisliği Ana Bilim Dalı
PROF. DR. OKAN ADDEMİR
- Metal alkoksitlerin vic-dioksim ve pridil monoksim ligantlarıyla kompleksleştirilmesi, kompleks yapılarının aydınlatılması
Complexation of metal alkoxides with vic- dioxime and pyridyl monoxime ligands, characterisation of the complex structure
ÖZGÜR AKTAŞ