Developing test procedure and design of fixture for dynamic test of road ambulances
Karayolu ambulanslarının dinamik testleri için test prosedürünün geliştirilmesi ve fikstür tasarımı
- Tez No: 595299
- Danışmanlar: PROF. DR. MUSTAFA İLHAN GÖKLER
- Tez Türü: Yüksek Lisans
- Konular: Makine Mühendisliği, Mechanical Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2019
- Dil: İngilizce
- Üniversite: Orta Doğu Teknik Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Makine Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: Belirtilmemiş.
Özet
Karayolu ambulanslarının karıştığı trafik kaza sayıları artış göstermektedir. Bu durum hasta taşıma kabininde taşınan hastaların ve sağlık çalışanlarının ölüm ve yaralanma risklerini arttırmaktadır. Bu nedenle, yolcular için daha güvenli bir ortam sağlanması önemli hale gelmiştir. Karayolu ambulanslarında kullanılan tıbbi cihazlar, çekmeceler, sedye sistemleri yolcuların güvenliğini tehlikeye atmayacak şekilde tutturulmalıdır. Bu amaç için tasarlanan sabitleme sistemlerinin uygunluğu, EN 1789+A2 standardının gerektirdiği şekilde, ambulans hasta taşıma kabinlerinin 10 g dinamik sled testlerinin gerçekleştirilmesi vasıtası ile doğrulanmalıdır. Bu standartta belirtilen kurallar test sonuçlarının değerlendirilmesi sırasında bazı belirsizlikler yaratmaktadır. Bu çalışmada, test numune hazırlığının uygun şekilde yapılabilmesi, testlerin gerçekleştirilmesi ve test sonuçlarının değerlendirilebilmesi için yeni bir test prosedürü önerilmiştir. EN 1789+A2 standardına göre farklı yönlerden (ön, arka, sol, sağ ve dikey) 10 g testleri gerçekleştirilmektedir. Dinamik testlerin yapılması sırasında test numunesinin slede bağlanabilmesi için METU-BİLTİR Merkezi Araç Güvenlik Birimi'nde fikstürler kullanılmaktadır. Dikey yönde kullanılan test fikstürün dinamik analiz çalışmaları Sonlu Elemanlar Analizi (SEA) programı Ls-DYNA kullanılarak gerçekleştirilmiştir. Analiz sonuçları ve mevcut kullanılan fikstürün test sırasında deformasyonu gözlemlenerek sonuçlar karşılaştırılmıştır. Dikey yön testi için fikstür tasarımının iyileştirilmesi gerektiği değerlendirilmiştir. Tamamen yeni iki test fikstürü ve şu anda kullanılan fikstür üzerinde modifiye edilmiş bir tane test fikstürü tasarlanmış ve SEA gerçekleştirilmiştir. Bu üç alternatif test fikstürünün plastik deformasyonu düşürerek şu anda kullanılan fikstür üzerinde avantajlar sağladığı görülmüştür.
Özet (Çeviri)
The number of traffic accidents involving road ambulances is increasing. This situation increases the risk of death and injury of the patients and healthcare workers transported in the patient transport cabin of the road ambulances. Therefore, providing a safer environment for these occupants has become important. Medical devices, drawers, stretcher systems used in the road ambulances should be secured to avoid endangering safety of the occupants. The conformity of the fixing systems designed for this purpose must be verified by performing the 10 g tests of ambulance patient transport cabin in a sled test facility as required by EN 1789+A2 standard. The rules described in the standard cause some ambiguities during the evaluation of the test results. In this study, a new test procedure has been proposed in order to prepare the test sample properly, conduct tests and evaluate test results for the road ambulance tests. According to EN 1789+A2 standard, the 10 g tests are performed for five different directions (front, back, left, right, vertical). In METU-BILTIR Center Vehicle Safety Unit, the fixtures are used to fasten the test sample (i.e. ambulance cabin) to the sled during the tests. Dynamic analysis of the test fixture used for vertical direction has been performed by using Finite Element Analysis (FEA) Software Ls-DYNA. The results of FEA and deformations of the currently used test fixture during the tests have been observed and compared. It has been evaluated that the design of the fixture for the vertical direction test should be improved. Two completely new test fixtures and one with modifications on the currently used fixture are designed and FEA for these have been realized. It has been seen that these three alternative test fixtures provide advantages over the currently used fixture by decreasing plastic deformation.
Benzer Tezler
- Esnek üretim sistemlerinin tasarımı ve çizelgelemesi
Design and scheduling of flexible manufacturing systems
AHMET MURAT PORAY
Yüksek Lisans
Türkçe
1995
Endüstri ve Endüstri Mühendisliğiİstanbul Teknik ÜniversitesiDOÇ.DR. M. BÜLENT DURMUŞOĞLU
- IEEE 1149.1 standardı kullanarak test edilebilir lojik devre tasarımı
Testable lojik circit design by using IEEE 1149.1 standard
A.BETÜL TUNCER
Yüksek Lisans
Türkçe
1992
Elektrik ve Elektronik Mühendisliğiİstanbul Teknik ÜniversitesiPROF. DR. AHMET DERVİŞOĞLU
- Design, manufacturing and testing of an ethanol/lox bi-propellant rocket engine with a focus on the mass flow control
Etanol/lox sıvı yakıtlı roket motorunun kütle akış kontrolü odaklı tasarımı, üretimi ve testleri
İBRAHİM SAFA UÇ
Yüksek Lisans
İngilizce
2022
Mühendislik BilimleriBoğaziçi ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
DOÇ. DR. MURAT ÇELİK
- Design and analyses of porous concrete for safety applications
Başlık çevirisi yok
AYDA ŞAFAK AĞAR ÖZBEK
Doktora
İngilizce
2016
İnşaat MühendisliğiTechnısche Unıversıteıt Delft (delft Unıversıty Of Technology)PROF. DR. K. VAN BREUGEL
- Kalça protezleri için aşınma test cihazı tasarımı
Design of wear tester for hip prostheses
DERYA KARAMAN
Yüksek Lisans
Türkçe
2019
Makine Mühendisliğiİnönü ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
DR. ÖĞR. ÜYESİ ERKAN BAHÇE