Çelik sacların şekillendirme kabiliyeti
Başlık çevirisi mevcut değil.
- Tez No: 3032
- Danışmanlar: YRD. DOÇ. DR. A. İRFAN YÜKLER
- Tez Türü: Yüksek Lisans
- Konular: Metalurji Mühendisliği, Metallurgical Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 1987
- Dil: Türkçe
- Üniversite: Marmara Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Belirtilmemiş.
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: Belirtilmemiş.
Özet
Özet yok.
Özet (Çeviri)
- 2 - SUMMARY The old method of hand forming of sheet steel is today used primarily as a finishing operation to remove wrinkles left by forming machines. In the metalworking in dustries hand forming is primarily limited to experimental work where only a few identical pieces are required. Most high production volume sheet metal forming is done on a press, driven by either mechanical or hydraulic action. The basic tools used with a press are the punch and the die. Although there are many forming methods, two of them are more important: Stretch forming and deep drawing. St retch forming is the process of forming by the application of primarily tensile forces in such a way as to stretch the material over a tool or form block. Deep drawing is the metalworking process used for shaping flat sheets into cup shaped articles. This forming is done by pressing the metal sheet into a die with a punch. Because of the complexity of sheet forming ope rations, simple mechanical property measurements made from the tension test are of limited value. Over the years many laboratory tests have been developed to evaluate the forma- bility of sheet metals. A deep drawing test is developed in terms of limiting draw ratio. In Erichsen test the sheet is clamped between two ring dies while a punch, usually a ball, is forced agains the sheet until it fractures. The depth of the bulge before the sheet fractures is measured. This test subjects the sheet primarily to stretching. Howe ver, most practical sheet forming operations provide a com bination of both biaxial stretching and deep drawing. The limit strains are represented best by Forming Limit Diagrams (FLD). Hence, the FLD determines the limit of useful defor mation in sheet forming and controls failure.- 3 FLD is usually obtained by performing tension tests, deep drawing tests, Erichsen tests and bulge tests. Representation of fracture data as a plot of major versus minor strains at the fracture gives the limit curve. Frac ture occurs when the strain ratio at the end of the process is above the limit curve. The direction and magnitude of maximum strain are easily determined by a grid pattern of small diameter circles on the surface of the blank. The surface of the blank is covered by a grid of circles, pro duced by electrochemical marking before the tests. During forming, the circles are deformed into ellipses. The direc tion of maximum strain corresponds to the major axes of el lipses and the magnitude of that strain is determined by measuring the increase in length of the ellipses over the diameters of the circles. The minimum strains are also de termined by the same process. Formability is a function of both material pro perties (strain hardening exponent
Benzer Tezler
- Paslanmaz çelik sacların perin çekilmesinde işlem karekteristikleri
Başlık çevirisi yok
İBRAHİM ŞAHİN
Yüksek Lisans
Türkçe
1994
Makine MühendisliğiYıldız Teknik ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
PROF. DR. MEHMET EMİN YURCİ
- Derin çekme saclarında derin çekilebilirlik özelliklerinin belirlenmesi
Determination of formability characteristics on steel sheets
TANSU GÜNDÜ
- Çok düşük karbonlu çeliklerin sac şekillendirilebilirliği
Başlık çevirisi yok
M.BİNNAZ AKSAKAL KUNAÇ
Yüksek Lisans
Türkçe
1998
Makine Mühendisliğiİstanbul Teknik ÜniversitesiMakine Malzemesi ve İmalat Teknolojisi Ana Bilim Dalı
DOÇ. DR. MEHMET DEMİRKOL
- Soğuk şekillendirilmiş saçların kaynağı
Cold formed of sheets steels welding
ŞÜKRÜ YİĞİT
Doktora
Türkçe
1997
Eğitim ve ÖğretimMarmara ÜniversitesiMetal Eğitimi Ana Bilim Dalı
PROF. DR. A. İRFAN YÜKLER