Yüzey akustik dalga esasına dayanan filtre ve rezonatörlerin analizi ve tasarımı
Analysis and design of surface acoustic wave filters and resonators
- Tez No: 22068
- Danışmanlar: PROF. DR. ERGÜL AKÇAKAYA
- Tez Türü: Yüksek Lisans
- Konular: Elektrik ve Elektronik Mühendisliği, Electrical and Electronics Engineering
- Anahtar Kelimeler: Akustik dalga, Filtreler, Rezonatör, Tasarım, Acoustic wave, Filters, Resonator, Design
- Yıl: 1992
- Dil: Türkçe
- Üniversite: İstanbul Teknik Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Belirtilmemiş.
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: Belirtilmemiş.
Özet
electrode position and the apodisation function required to reproduce a desired waveform. This procedure is applicable to the design of weighted dispersive filters. Surface wave techniques can be used to produce several types of stable oscillator using SAW resonator. The resonator is basically two reflectors forming a surface wave cavity and a transducer which are used to generate a surface wave packet on the surface. The reflectors are periodic arrays of either metal strips or grooves and reflect when their period is equal to half the SAW wavelength and there is corresponding increase in the array transmission loss. With a large number of strips or grooves, the array reflection coefficient can be very close to unity. For YZCY-cut Z-propagatingD lithium niobate which has an impedance discontinuity of 1.2%, 300 metallic strips are required in the array for a reflection coefficient of 98%. The resonator can give very high Q factors, up to 20,000, giving good stability. Furthermore, highly stable c. w. sources with frequencies up to about 2 GHz can be obtained by using SAW resonators. In this thesis, it will be given an analysis and synthesis procedure using transmission line model for the reflectors. The basic resonator structure is illustrated in Figure 3. Grooved array reflector substrate Figure 3. Two-port surface acoustic wave resonator CXID
Özet (Çeviri)
The applicability of surface wave devices to practical electronic systems is basically determined by the centre frequencies, bandwidths and delays obtainable. The upper limit for the centre frequency is determined by fabrication techniques, and current lithography is about 1.5 GHz. At low frequencies SAW devices become more bulky and expensive and other technologies become more suitable, for example bulk acoustic wave resonators for bandpass filters or digital techniques for signal processing. Consequent 1 y-, SAW devices are not normally used below a few MHz. In most applications this frequency range implies that the devices are used in the I. F. section of ' the system and this has the important consequence that low insertion loss is not generally a priority. For example, bandpass filters have typically 15 to 30 dB loss, and this is acceptable for many applications. Bandwidths generally range from a minimum of about lOO kHz to a maximum of about 50% of the centre frequency. CXIIZ)electrode position and the apodisation function required to reproduce a desired waveform. This procedure is applicable to the design of weighted dispersive filters. Surface wave techniques can be used to produce several types of stable oscillator using SAW resonator. The resonator is basically two reflectors forming a surface wave cavity and a transducer which are used to generate a surface wave packet on the surface. The reflectors are periodic arrays of either metal strips or grooves and reflect when their period is equal to half the SAW wavelength and there is corresponding increase in the array transmission loss. With a large number of strips or grooves, the array reflection coefficient can be very close to unity. For YZCY-cut Z-propagatingD lithium niobate which has an impedance discontinuity of 1.2%, 300 metallic strips are required in the array for a reflection coefficient of 98%. The resonator can give very high Q factors, up to 20,000, giving good stability. Furthermore, highly stable c. w. sources with frequencies up to about 2 GHz can be obtained by using SAW resonators. In this thesis, it will be given an analysis and synthesis procedure using transmission line model for the reflectors. The basic resonator structure is illustrated in Figure 3. Grooved array reflector substrate Figure 3. Two-port surface acoustic wave resonator CXIDThe applicability of surface wave devices to practical electronic systems is basically determined by the centre frequencies, bandwidths and delays obtainable. The upper limit for the centre frequency is determined by fabrication techniques, and current lithography is about 1.5 GHz. At low frequencies SAW devices become more bulky and expensive and other technologies become more suitable, for example bulk acoustic wave resonators for bandpass filters or digital techniques for signal processing. Consequent 1 y-, SAW devices are not normally used below a few MHz. In most applications this frequency range implies that the devices are used in the I. F. section of ' the system and this has the important consequence that low insertion loss is not generally a priority. For example, bandpass filters have typically 15 to 30 dB loss, and this is acceptable for many applications. Bandwidths generally range from a minimum of about lOO kHz to a maximum of about 50% of the centre frequency. CXIIZ)electrode position and the apodisation function required to reproduce a desired waveform. This procedure is applicable to the design of weighted dispersive filters. Surface wave techniques can be used to produce several types of stable oscillator using SAW resonator. The resonator is basically two reflectors forming a surface wave cavity and a transducer which are used to generate a surface wave packet on the surface. The reflectors are periodic arrays of either metal strips or grooves and reflect when their period is equal to half the SAW wavelength and there is corresponding increase in the array transmission loss. With a large number of strips or grooves, the array reflection coefficient can be very close to unity. For YZCY-cut Z-propagatingD lithium niobate which has an impedance discontinuity of 1.2%, 300 metallic strips are required in the array for a reflection coefficient of 98%. The resonator can give very high Q factors, up to 20,000, giving good stability. Furthermore, highly stable c. w. sources with frequencies up to about 2 GHz can be obtained by using SAW resonators. In this thesis, it will be given an analysis and synthesis procedure using transmission line model for the reflectors. The basic resonator structure is illustrated in Figure 3. Grooved array reflector substrate Figure 3. Two-port surface acoustic wave resonator CXIDThe applicability of surface wave devices to practical electronic systems is basically determined by the centre frequencies, bandwidths and delays obtainable. The upper limit for the centre frequency is determined by fabrication techniques, and current lithography is about 1.5 GHz. At low frequencies SAW devices become more bulky and expensive and other technologies become more suitable, for example bulk acoustic wave resonators for bandpass filters or digital techniques for signal processing. Consequent 1 y-, SAW devices are not normally used below a few MHz. In most applications this frequency range implies that the devices are used in the I. F. section of ' the system and this has the important consequence that low insertion loss is not generally a priority. For example, bandpass filters have typically 15 to 30 dB loss, and this is acceptable for many applications. Bandwidths generally range from a minimum of about lOO kHz to a maximum of about 50% of the centre frequency. CXIIZ)electrode position and the apodisation function required to reproduce a desired waveform. This procedure is applicable to the design of weighted dispersive filters. Surface wave techniques can be used to produce several types of stable oscillator using SAW resonator. The resonator is basically two reflectors forming a surface wave cavity and a transducer which are used to generate a surface wave packet on the surface. The reflectors are periodic arrays of either metal strips or grooves and reflect when their period is equal to half the SAW wavelength and there is corresponding increase in the array transmission loss. With a large number of strips or grooves, the array reflection coefficient can be very close to unity. For YZCY-cut Z-propagatingD lithium niobate which has an impedance discontinuity of 1.2%, 300 metallic strips are required in the array for a reflection coefficient of 98%. The resonator can give very high Q factors, up to 20,000, giving good stability. Furthermore, highly stable c. w. sources with frequencies up to about 2 GHz can be obtained by using SAW resonators. In this thesis, it will be given an analysis and synthesis procedure using transmission line model for the reflectors. The basic resonator structure is illustrated in Figure 3. Grooved array reflector substrate Figure 3. Two-port surface acoustic wave resonator CXIDThe applicability of surface wave devices to practical electronic systems is basically determined by the centre frequencies, bandwidths and delays obtainable. The upper limit for the centre frequency is determined by fabrication techniques, and current lithography is about 1.5 GHz. At low frequencies SAW devices become more bulky and expensive and other technologies become more suitable, for example bulk acoustic wave resonators for bandpass filters or digital techniques for signal processing. Consequent 1 y-, SAW devices are not normally used below a few MHz. In most applications this frequency range implies that the devices are used in the I. F. section of ' the system and this has the important consequence that low insertion loss is not generally a priority. For example, bandpass filters have typically 15 to 30 dB loss, and this is acceptable for many applications. Bandwidths generally range from a minimum of about lOO kHz to a maximum of about 50% of the centre frequency. CXIIZ)
Benzer Tezler
- Akustik yüzey dalga esasına dayanan filtrlerin analizi, tasarımı ve GSM sistemindeki uygulamaları
Analysis and design of saw filter and saw filter applications in GSM
H.CEMİL KARAGÜZEL
Yüksek Lisans
Türkçe
1997
Elektrik ve Elektronik Mühendisliğiİstanbul Teknik ÜniversitesiElektronik ve Haberleşme Mühendisliği Ana Bilim Dalı
PROF. DR. ERGÜL AKÇAKAYA
- İki boyutlu elastik dalga yayınımının sonlu-fark yöntemiyle modellenmesi
The Modelling of the propagation of two dimensional elastic wave by finite-difference method
ZEYNEP KÖMÜRCÜ
Yüksek Lisans
Türkçe
1994
Jeofizik MühendisliğiKaradeniz Teknik ÜniversitesiJeofizik Mühendisliği Ana Bilim Dalı
YRD. DOÇ. DR. VELİ KARA
- Küresel ve silindirik koordinatlarda artık değişken yöntemi
Residual variable method in spherical and cylindrical coordinates
FATMA ERDOĞAN
Doktora
Türkçe
1987
Fizik ve Fizik MühendisliğiAnkara ÜniversitesiFizik Ana Bilim Dalı
PROF. DR. NURİ AKKAŞ
- Çok cisimli ses alanlarının Helmholtz integral denklemi ile hesaplanması
The Computation of multibody acoustic fields by Helmholtz integral equation
AYŞE SAİDE SARIGÜL
- The V-Groove lens
V-Oluklu mercek
AYHAN BOZKURT
Yüksek Lisans
İngilizce
1994
Elektrik ve Elektronik MühendisliğiKaradeniz Teknik ÜniversitesiElektrik ve Elektronik Mühendisliği Ana Bilim Dalı
PROF. DR. HAYRETTİN KÖYMEN
PROF. DR. ABDULLAH ATALAR