Ağaç ve tomruk hacimlerinin tahmininde kullanılan bazı yöntemlerin karşılaştırılması
Comparison of some formulas and methods in estimating log and tree bole volumes
- Tez No: 200512
- Danışmanlar: Y.DOÇ.DR. RAMAZAN ÖZÇELİK
- Tez Türü: Yüksek Lisans
- Konular: Ormancılık ve Orman Mühendisliği, Forestry and Forest Engineering
- Anahtar Kelimeler: Tomruk Hacmi, Ağaç Hacmi, Centroid, Paracone Method, Orman kaynakları, Ormancılık, Log volume, Tree Bole Volume, Centroid Method, Paracone Method, Forest resources, Forestry
- Yıl: 2007
- Dil: Türkçe
- Üniversite: Süleyman Demirel Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Orman Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: Belirtilmemiş.
Özet
Bu çalışmada; Ağaç ve tomruk hacim tahminlerinde kullanılan bazı yöntemlerin karşılaştırması yapılmıştır. Bu amaçla; Kızılçamdan (Pinus brutia Ten.) 140, Toros göknarından (Abies cilicica Carr.) 178 ve Toros sedirinden (Cedrus libani A. Rich.) de 180 ağaç gövdesi üzerinde ayrıntılı ölçüm yapılmıştır. Yine farklı uzunluklardaki (6 m ve 12 m) tomruk hacim tahminlerinin karşılaştırılması için, Kızılçamdan 209 adet, Toros göknarından 291 ve Toros sedirinden de 243 adet tomruk üzerinde ayrıntılı ölçümler yapılmıştır. Ağaç ve tomruk hacim karşılaştırmalarında kullanılmak üzere gerekli gerçek hacim değerleri kısa aralıklarla ölçülen seksiyon hacimlerinin toplamları olarak bulunmuştur. Sonuçların değerlendirilmesinde DOSATEST isimli bir paket program kullanılmıştır. En yaygın yöntemin belirlenmesinde; Ortalama hata yüzdesi (bias veya sistematik hata), tolerans aralığı yüzdesi ve hata kareler ortalaması ölçütleri kullanılmıştır. Bu ölçütlere göre ağaç hacim tahminleri için en uygun yöntemlerin her üç ağaç türü için de sırasıyla, Paracone Method, Control-variate-2 ve Centroid Method yöntemleri olduğu görülmüştür. Hata yüzdesi en yüksek olan yöntem ise Yerel Hacim Tablolarıdır. Farklı uzunluklardaki tomruk hacimleri için yapılan değerlendirmede ise; en başarılı yöntemlerin sırasıyla; Gravity Method, Centroid Method ve Newton-Riecke yöntemleri olduğu görülmüştür. Burada en yüksek hata oranı veren yöntemler ise; Smalian, Bruce ve Patterson-Doruska yöntemleri olarak bulunmuştur. Sonuç olarak; ülkemizde ağaç gövde hacimlerinin tahmininde uzun yıllardır kullanılan Yöresel Hacim Tablolarının oldukça hatalı sonuçlar verdiği, Paracone Method, Centroid Method veya Control-variate-2 yöntemlerinin kullanılması ile daha doğru hacim tahminlerinin yapılabileceği, benzer şekilde tomruk hacmi belirlenmesi gereken çalışmalarda da Huber ve Smalian yöntemleri yerine Gravity Method ya da Centroid Method yöntemlerinin kullanılması önerilebilir.
Özet (Çeviri)
In this study, we compared some standard or modern formulas and methods for estimating tree bole volume and log volume. For this aim, tree bole volumes of 178 Taurus fir (Abies cilicica Carr.), 140 trees of Brutian pine (Pinus brutia Ten.), and 180 Taurus cedar (Cedrus libani A. Rich.) were estimated using the Paracone Model, Centroid Method, Control-variate Method, Huber formula, and local volume tables (LVT). For 12 meters and 6 meters log volumes estimations of 291 Taurus fir (Abies cilicica Carr.), 209 trees of Brutian pine (Pinus brutia Ten.), and 243 Taurus cedar (Cedrus libani A. Rich.) were estimated using the Paracone model, Centroid method, Control-variate method and center of gravity, center of volume, Bruce formula, Newton formula, Patterson-Doruska method. Data were analyzed and evaluated by methods and the related DOSATEST program. These estimates were compared with ?true? volume of each tree bole and log which was determined by aggregating the volumes of measured short sections using Smalian?s formula. The Paracone method was the only method with a bias not significantly different then zero. The Paracone method, Control-variate-2 and Centroid methods were clearly superior to the other formulae. Precision was better for Paracone method than other methods for all three species tested. For log volume estimations, the center of gravity method, center of volume method were the only methods with a bias not significantly different then zero. The center of gravity method, center of volume method, Newton formula were clearly superior to the other formulae. Precision was better for center of gravity than other methods for all three species tested. It would also indicate that continued use of The Smalian formula for estimating log volumes and Local volume tables for estimating tree bole volume for these species in Turkey will result in large volume estimations errors. As a result, the Paracone and Centroid methods are recommended for estimating tree bole volumes and center of gravity and center of volume methods for estimating log volume for these species in Turkey.
Benzer Tezler
- Tomruk üretiminde optimum boylama metodunun tek ağaç düzeyinde uygulanması
Applying a single tree level optimum bucking method during cut-to-length logging
NEŞE YENİLMEZ
Yüksek Lisans
Türkçe
2010
Ormancılık ve Orman MühendisliğiKahramanmaraş Sütçü İmam ÜniversitesiOrman Mühendisliği Ana Bilim Dalı
DOÇ. DR. ABDULLAH EMİN AKAY
- Artırılmış fonksiyon kabiliyetli tomruk yükleyici vinç üretimi ve performans parametrelerinin incelenmesi
Increased function capability loader crane production and investigation of performance parameters
DUYGU GİZEM İHTİYAROĞLU
Yüksek Lisans
Türkçe
2020
Ormancılık ve Orman MühendisliğiGiresun ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
DR. ÖĞR. ÜYESİ FARUK GÜNER
- Kontraplaklarda tomruk buharlama ve kaplama kurutma şartlarının formaldehit emisyonu üzerine etkileri
Başlık çevirisi yok
SEMRA ÇOLAK
Yüksek Lisans
Türkçe
1996
Ormancılık ve Orman MühendisliğiKaradeniz Teknik ÜniversitesiOrman Endüstri Mühendisliği Ana Bilim Dalı
Y.DOÇ.DR. GÜRSEL ÇOLAKOĞLU
- Çeşitli ağaç türlerinden elde edilen kaplamaların ıslanabilme yeteneği ve yapışma direnci üzerine bazı üretim şartlarının etkileri
The effects of some manufacturing conditions on wettability and bonding of veneers obtained from various wood species
İSMAİL AYDIN
Doktora
Türkçe
2004
Ormancılık ve Orman MühendisliğiKaradeniz Teknik ÜniversitesiOrman Endüstri Mühendisliği Ana Bilim Dalı
PROF.DR. GÜRSEL ÇOLAKOĞLU
- Batı Karadeniz bölgesi tomruk depolarında zarar yapan mantar türleri ve zarar tipleri
Wood decay fungi species and their damage types at log depots in Western Black Sea region
BURCU SERTKAYA
Yüksek Lisans
Türkçe
2017
Ormancılık ve Orman MühendisliğiDüzce ÜniversitesiOrman Endüstri Mühendisliği Ana Bilim Dalı
YRD. DOÇ. DR. MESUT YALÇIN