Toz metalurjisi yöntemiyle üretilen Fe-C-Mo-Cr7C3 kompozitinin abrasiv aşınma dayanımının araştırılması
The investigation of abrasive wear of Fe-C-Mo-Cr7C3 composite producted by powder metallurgy process
- Tez No: 134788
- Danışmanlar: YRD. DOÇ. DR. AHMET HASÇALIK
- Tez Türü: Yüksek Lisans
- Konular: Teknik Eğitim, Makine Mühendisliği, Technical Education, Mechanical Engineering
- Anahtar Kelimeler: Demir tozu, Kompozitler, Sürtünme aşınması, Toz metalurjisi, Powder metallurgy, ferrous based composites, abrasive wear, Iron powder, Composites
- Yıl: 2003
- Dil: Türkçe
- Üniversite: Fırat Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Makine Eğitimi Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: Belirtilmemiş.
Özet
Bu çalışmada Fe tozuna ağırlıkça % 3 oranında Mo, % 1.5 oranında C ve % 4, %8, %12 oranlarında (ortalama 25um, 50um, 80um tane boyutlarında) ferrokrom tozlan katılarak toz metalürjisi yöntemi ile üretilmiş olan Fe-C-Mo-Cr kompozitinin abrasiv aşınma davranışı üzerinde krom karbürün (Cr7C3) etkisi incelenmiştir. Deney çalışmalarında, üretilen numunelerin mikroyapıları optik mikroskop, Taramalı elektron mikroskobu SEM (Scanning Elektron Microscopy), EDS (Energy Dispersive Spectrograf) noktasal analiz çalışmaları ve X - Işınlan difraksiyonu (X - Ray Difraction) çalışmaları ile belirlenmiş ve mikrosertlikleri tespit edilmiştir. Aşınma testleri özel olarak imal edilmiş olan pin on disk aşınma test cihazında farklı yüklerde (ION, 20N, 3 ON) yapılarak numunelerin aşınma dirençleri tespit edilmiştir. Yapılan testler sonucunda, takviye elemanının tane boyutunun artmasıyla aşınma oranının arttığı ve deney şartlarında en iyi aşınma direncini ortalama 25um tane boyutundaki ağırlıkça %12 ferrokrom katkılı numunenin gösterdiği saptanmıştır. Çalışma altı bölümden oluşmaktadır. Birinci bölümde konuya giriş yapılarak ilgili literatür ve çalışmanın amacı verilmiştir. İkinci bölümde toz metalürji yöntemi açıklanmıştır. Üçüncü bölümde aşınma mekanizması, türleri, ölçüm teknikleri ve aşınmayı etkileyen faktörler incelenmiştir. Dördüncü bölümde deney ve ölçüm yöntemi açıklanmıştır. Beşinci bölümde deney sonuçlan tartışılarak yorumlanması ve son bölümde ise deneyler sonunda elde edilen sonuçlar verilerek, öneriler sunulmuştur.Anahatar Kelimeler : Toz metalürjisi, Fe esaslı kompozitler, abrasiv aşınma
Özet (Çeviri)
In this study, the effect of chrome carbide (O7C3) on abrasive wear of Fe-C-Mo- Cr7C3 composite produced by powder metallurgy, containing 3 wt.% Mo, 1,5 wt.% C and 4, 8, 12 wt.% Ferrochromium with the average particle size of 25 urn, 50um and 80um was investigated. In the experiments, microstnictures of the samples were examined by optic and Scanning electron microscopy, EDS (Energy Dispersive Spectrograph), X- ray diffraction method and microhardnes were measured. Wear resistances of samples were determined using different loads (ION, 20N, 30N) by pin on disc wear test machine developed for this experiment. In the experiments it has been found that with the increasing particle size of reinforcing element, wear rate increased and the 12 wt. % ferrocliromium reinforced sample showed the highest wear resistance in the experiment conditions. The study consists of six chapters. In the first chapter of study, introduction, literature related to the subject and purpose of study were given. In the second chapter, powder metallurgy was described. In the third chapter, the mechanisms of the wear, various wear types, measurement techniques and the factors affecting the wear were presented. In the fourth chapter, material and method were described. In the fifth chapter, the results were discussed and in the final chapter, general results and recommendation have been presented.
Benzer Tezler
- T/M paslanmaz çelik implantların üretimi ve teknolojik özellikleri üzerine bir araştırma
Production of P/M stainless steel implants and investigation on their technological properties
NACİ KURGAN
- AISI 4340 çeliğinin nitrürasyon ve GTA kaynak yöntemi ile yüzey modifikasyonu işlemleri sonrası mekaniksel davranışların araştırılması
The investigation of mechanical behavior of surface modification treatments, GTA welding process and nitriding of AİSİ 4340
SONER BUYTOZ
Doktora
Türkçe
2004
Metalurji MühendisliğiFırat ÜniversitesiMetalurji Eğitimi Ana Bilim Dalı
PROF.DR. MUSTAFA YILDIRIM
- Bor karbür oluşum koşullarının belirlenmesi ve toz karakterizasyonu
Determination of boron carbide formation reaction conditions and powder characterization
GÜLTEKİN GÖLLER
- Toz metalurjisi yöntemiyle üretilen kesici uçların proses, yapı ve mekanik özellik ilişkileri
Relations of the process, structure and mechanical properties of cutting tools which are produced by powder metallurgy method
OZAN YILMAZ
Yüksek Lisans
Türkçe
2006
Metalurji MühendisliğiYıldız Teknik ÜniversitesiMetalurji ve Malzeme Mühendisliği Ana Bilim Dalı
PROF.DR. ADEM BAKKALOĞLU
- Toz metalurjisi yöntemiyle üretilen Al-SiCp kompozitlerin difüzyon kaynak kabiliyetlerinin araştırılması
The investigation of the diffusion welding capability of the Al-SiCp composites produced through powder metallurgy method
HAMZA KÜÇÜKKARA